蜜桃Av久久精品人人槡_亚洲阿V天堂网2019无码_亚洲精品不卡无码福利在线观看_免费人成网站视频在线观看国内_高潮一区_观看亚洲色欲色欲色欲WWW

歡迎來到東莞市艾維品實業有限公司官網!

東莞市艾維品實業有限公司

專業研發、生產、銷售各種花紋的水轉印膜

全國咨詢熱線

400-0253-888

新聞資訊

新聞中心

當前位置: 首頁 > 新聞中心 > 臺州公司新聞

聯系我們Contact Us

東莞市艾維品實業有限公司

聯系人: 董先生/Abe Dong

手 機:13378609888

 箱:dgivip@163.com

 址:廣東省東莞市樟木頭鎮金河社區濱河路31號

網 址:m.511kan.com.cn

臺州水轉印加工技術操作方法

2023-06-02 09:02:52

1. 確定適當水溫 (20 °C – 30°C),水面保持溢流狀態。

Make sure the proper water temperature (20 °C - 30 °C), keep water at overflow state.


2. 保持水表面無活化劑殘留及雜質。

Keep the water surface without activator residues and impurities.


3. 置膜,以適當角度將膜平放于水面(確定膜之正反面,印刷層朝上)

Put the film on the water flatly with the proper angle.( Confirm the film positive & negative, printing side up)


4.配合水溫設定溶解時間,水溫一般為25-30度,溶解時間約為45秒到2分鐘

Set dissolution time with water temperature which is often 25°C-30 °C. The dissolution time is about 45 seconds to 2 minutes.


5.視印刷油墨之厚度,判定噴涂活化劑之時間,油墨層越厚,可在膜尚未完全溶解時,提前噴涂活化劑,讓油墨活化時間加長,而一般作業情況溶解1分鐘左右可噴涂活化劑,待膜成鏡面而平坦擴展(5秒-15秒)即可上膜、轉印。

Spray activator time depends on the thick of printing ink. The thicker the ink layer, spray activator in advance before the film not yet completely dissolved, to make the ink activate time much longer. General operation condition is about 1 minute to dissolve, then spray activator. After flat extension of the film (5 seconds -15 seconds), then put the film to be printed and transferred .


6. 在上膜之前需視加工物之外形或有紋路性,選擇下水角度,以利于空氣排出。

Select water down angle to exhaust air well as the dip items' shape or lines prior to film transfer . 


7. 上膜后,不可立即拿起,應在水中搖晃3-5秒,切斷邊緣之膜,增加紋路咬住被加工物之時間。

Do not take out the work piece immediately after transfer the film. Shake it on the water for 3-5 seconds, to cut the edge's film and increase the lines to bite work piece's time.


8. 活化劑噴涂需以0.8mm*4孔噴槍及可攪拌式壓力操作業,噴涂距離約30cm,空氣壓力適當調整避免花紋脫落,不可有水花產生,必要時水溫可加到35°C, 水槽之水量需作溢, 最后一道水需干凈,沖洗完成需經空氣吹干并經品管修整再入烘烤爐。

Spray activator with 0.8mm * 4 hole spray gun and operate by stirred pressure. Spray distance is about 30cm. Adjust air pressure properly to avoid the film pattern fall off, and water can't be splashed. Add water temperature to 35 °C if necessary. The tank water is overflow and the last water must be clean. After rinse, then dry by oven. 


不同的圖案,必須使用不同的底色,如木紋基本使用棕色、咖啡色、土黃色等,石紋基本使用白色等.

 Different film pattern , different base coat. e.g. Wood grain (often Brown, khaki), Marble grain (often white etc).


近期瀏覽:

相關產品

相關新聞

contact us

東莞市艾維品實業有限公司

廣東省東莞市樟木頭鎮金河社區濱河路31號

水轉印膜丨水轉印耗材丨水轉印設備

水轉印產品代加工丨水轉印技術支持

水轉印開發、生產、加工、銷售、培訓一條龍服務

contact us

         


         掃一掃 添加微信

SERVICE

聯系人:(董先生)

133-7860-9888

全國熱線

400-0253-888

座機

0769-81723888

0769-87123588

24小時在線客服
主站蜘蛛池模板: 欧美成人一区二区三区在线观看 | 欧美成人午夜不卡免费 | 欧美性色欧美A在线播放 | 久久国产亚洲精品赲碰热 | 可以在线看的毛片网站 | 欧美成人一区二区三区片免费 | 99久久精品免费 | 国产字幕在线看 | 中文字幕在线视频一区二区三区 | 国产免费无码AV在线观看 | 日韩高清在线观看永久 | 少妇人妻无码专区视频 | 亚洲中文无码一区二区三区在线观看 | 观看国产色欲色欲色欲www | 国产精品爆乳在线播放 | 亚洲精品天天 | 亚洲AV人无码综合在线观看 | 97久久超碰国产精品 | 欧美巨大巨粗黑人性aaaaaa | 99九九热只有国产精品 | 亚洲中文字幕永久在线天堂 | 蜜桃精品在线 | 国产激情视频一区二区三区 | 午夜国产成人 | 欧洲色情三级欧美三级视频 | 欧美A级毛欧美1级A大片 | 欧美另类videos | 97影院理论午夜伦不卡 | 中文字幕人妻熟女人妻A片 91婷婷韩国欧美一区二区 | 色偷偷偷亚洲综合网另类 | 亚洲一区二区三区四区av | 国产精品国产三级国产AV中文 | 国产成人综合亚洲AV | 2020国自产拍精品露脸快速 | 一本大道Av伊人久久综合 | 日韩做A爰片久久毛片A片 | 亚洲精品制服校园无码 | 51久久夜色精品国产水果派解说 | 国产AV夜夜欢一区二区三区 | 午夜久久久久久久久 | 久久中国|